Vision TC3-HDMITP HDMI Over Cat5e/Cat6 50m 3446574

Vision TC3-HDMITP HDMI Over Cat5e/Cat6 50m 3446574

Vision TC3-HDMITP 3446574

Our Price:  £92.98(Exc. 20% VAT)(£111.58 Inc. VAT)

Order Code:  3446574
Part Number:  TC3-HDMITP
Manufacturer:  VISION



Approx 95 Units Available

Vision TC3-SURR2G AV Wall Plate 2 Gang Frame 3446603Vision TC3-SURR2G AV Wall Plate 2 Gang Frame 3446603
Vision TC3-SURR1G AV Wall Plate 1 Gang Frame 3446602Vision TC3-SURR1G AV Wall Plate 1 Gang Frame 3446602


Vision Audio Visual : Installation : Innovation


Vision TC3-HDMITP converts HDMI signals and transmits them over ethernet Cat5e upto 30m or hdmi over ethernet Cat6 upto 50m and supports 1080P (1920 x 1080) and 3D (30hz) TC3-HDMITP is a pear to pear device and cannot be connected over a live network infrastructure or through a routers (See TC3-HDMIIP) 

Peet To Peer
Vision’s “Techconnect Twist” products allow a variety of signals to be transmitted long distances over standard unshielded CAT5e and CAT6 cable. Sold as a transmitter and receiver set, the ‘TC2 HDMITP’ enables use of inexpensive and flexible UTP (unshielded twisted pair) cable to route HDMI signal from a computer to a display device. (CAT5e / Cat6 cables not supplied) 

Faster Installation
With the Vision TC3-HDMITP Installers can take advantage in buildings which have been flood-wired with network cable. Where a CAT5e cable is already in place the installation is super-fast.

Techconnect Module
The Vision TC3-HDMITP transmitter presents as an ordinary Techconnect HDMI module from the front, allowing tidy clip-in installation. The circuit on rear of the module is packed with technology.

HD Resolution
The TC3-HDMITP supports resolutions up to 1080P (1920 x 1080) at 60 frames per second. It also supports 3D at 30Hz.

Cable Length
With a 1920 x 1080 resolution signal the CAT5e cable can be up to 30m long. CAT6 cable takes this maximum recommended length up to 50m. With common 1280 x 800 resolution the cables can be longer because of the reduced bandwidth required: 30m on CAT5e cable, and 50m on CAT6 cable.

Dual Power
Two power supplies are included with the Vision TC3-HDMITP, one for the transmitter, and one for the receiver. The complex HDMI signal uses all four pairs of wires inside the CAT5e and CAT6 cables, so it is not possible to also carry power over the cable.

HDCP Support
Version 1.2 of HDCP (High-bandwidth Digital Content Protection) is supported. HDCP authentication is the technology developed by Intel that prevents copying of digital content as it passes through cables.

Full EDID handshake is supported, which allows the source device to output the native display resolution. A reset button on the transmitter can be pressed to capture information from the display if the display is changed.

Easier to work with
Compared to long HDMI cables Ethernet cable is easier to work with; it has a tighter bend-radius, is thinner, easier to pull, and simple to terminate.

Maximum cable length: Standard Ethernet rules apply:
CAT5e: 1280 x 1024: 50m / 1600 x 1200: 40m / 1920 x 1080: 30m 
CAT6: 1280 x 1024: 60m / 1600 x 1200: 55m / 1920 x 1080: 50m

CAT5e: 30m between TX and RX devices
CAT6: 60m between TX and RX devices
Maximum resolution: 1080p@50/60Hz and 3D @ 30Hz
Operating temperature range: -15 to +55 oc 
Operating humidity range: 5~90% RH no condensation
Power Consumption: 3 Watts (max) each (Transmitter and Receiver)

Customers who bought this item also bought:


Vision Techconnect Wall Plates - Vision Amplifiers - Vision Techconnect Face Plates - Techconnect HDMI Wall Plate Socket - VGA Module
Techconnect Cables - Sky HD Wall plates - Vision Techconnect Wall Amplifier - Techconnect Control - Techconnect Tilt - Vision Wall Speakers